The Stihl MS 192T is a professional tree trimming chainsaw. It does its work flawlessly. It is a great saw for climbing because of being very lightweight. It has a simple design and its body is made of plastic. But that does not hamper its performance as it can cut up to 8″ limbs. The Sthil MS 192 T has excellent value for money and it is very long lasting.
However, you might slowly start to encounter with some issues while handling the Stihl MS 192T for a year or two. Starting problems, carburetion issue, gauze strainer in the carb, clutch problems and running problems are the common problems of a Stihl chainsaw. So, today we are going to discuss about the common problems of STihl MS 192I.
Common Problems of Stihl MS 192T:
When you know the reasons behind an issue it becomes easier to solve. Also, you need to know the solving process to solve the issues by yourself. So, the reasons and the possible solutions of Stihl MS 192T chainsaw are discussed below:
1. Starting Problem
Gasoline flow can be restricted by unclean or clogged fuel tanks, dirty fuel filters and lines, loose fuel hoses, dirty air filters, and a dirty carburetor. Before going on to the internal engine, inspect, clean, and repair all sections of the fuel system, as gas issues cause the bulk of starting issues.
Remove the air filter and inject some carburetor cleaner into the intake to solve the problem. This may be not enough to clear any debris and get it back in working order.
2. Carburetion Issue
The gasoline that rises above the height of the overflow pipe in the float chamber spills to the outside of the carb when the oil level in the float chamber is too high. Furthermore, there is no overflow conduit to allow for drainage to the outside. This causes the carburetion to overflow. It can be also caused by a bad float needle valve.
After the carburetor has been dismantled, spray carburetor cleaner into all of the holes and thoroughly clean everything. This is also an excellent time to check and modify the carburetor configurations to manufacturing specifications.
You might also need to drain the chamber and pour new fresh oil according to the instruction manual to solve this issue. If that does not solve your problem, you can seek help from an expert. However, if the needle valve is faulty then replacing it would solve the issue.
3. Faulty gauze strainer in the carb
This is an issue in the carburetor component. If the gauze strainer in the carb is damaged or faulty for some reason, it might problems like starting issues. So, you need to replace the gauze strainer if it is faulty or damaged.
4. Clutch Problems
If the engine is still running at regular rpm but the chain is slowing down, it’s a clutch issue. exhausted, gummed-up, or clogged springs, for example. If the engine loses revs when under load, it’s more than likely a fuel or carburetor issue.
The clutch sometimes begins to slide when the lining gets too thin to fulfill its function. There are two explanations for this. One is that the lining thins down to the point that the shoes don’t make full contact with the drum, and the other is that the shoe surfaces become slick.
When a clutch goes bad or starts to have problems, it can be hardly repaired or fixed. So, in this situation, the best option is to replace the clutch with a new one.
5. Running Problem
Your chainsaw running thne suddenly stopping an be the sign of running problems. This can happen when carburetor is out of whack or it may just be a ignored air filter that is blocked. This can also lead to carburetor issues as the carburetor’s air-to-gasoline ratio will be compromised if the filter is blocked. This can result in a blocked spark wire screen within the exhaust and a damaged spark plug.
To solve this problem, all you need to do is to clean the clogged and blocked carburetor and filters. Clean the spark arrester screen and the spark plug if the engine still won’t start or runs rough after clearing the air filter. If the problem is still present for a long time, you may need to replace the spark plug.
Frequently Asked Questions
Why does my Stihl chainsaw bog down when I give it gas?
You might be using your Stihl chainsaw at altitude or you may have simply adjusted the carburetor incorrectly, which is why it bogs down when you give it gas. Dirty air filters, spark arrestors, or carburetors will also cause the saw to run poorly at speed.
What is the life expectancy of a Stihl chainsaw?
Chainsaws from Stihl have a 2,000-hour run duration. That implies the saw will last you at least 5.5 years before it dies. Keep in mind that this time is for professional chainsaws, not for household chainsaws.
What would cause a chainsaw to bog down when accelerating?
There are a number of reasons why your saw might not be working properly. It’s possible that the carburetor, spark arrestor, or air filter are clogged. It’s also possible that the carburetor adjustment slipped. This article will go through some of the reasons why your chainsaw is bogging down, as well as how to remedy it.
Sthihl Chainsaws are one of the best chainsaws in the market for completing all your garden work whether you are a using it for personal purpose or or professiona usel. Stihl MS 192T is one of the best model of Stihl that you can easily trust and rely on. And with regular troubleshooting and maintenance you can reduce the chances of having issues frequently.
- 7 Common STIHL BR 800 Problems And Solutions
- Top 7 Common stihl 500i Problems And Solutions
- Most Common Stihl 362 Problems And Solutions